Selfhosted

The best way is to have a small server with wireguard installed, which is a VPN. This runs on virtually anything, including a raspberry pi or even a router with open-wrt.

Anyways, your wireguard server will only accept connections from devices that have its certificate (secure passwordless authentication).

Once you're connected to that VPN, it's effectively as being in your home network.

You might want to Google for guides on how to setup wireguard on a raspberry pi. Even if you don't have a PI you'll surely find the tutorial you need.

You’re probably looking for Tailscale. Simple to use, free plan, extensible and powerful.

The safest (but not as convenient) way is to run a VPN, so that the services are only exposed to the VPN interface and not the whole world.

In pfsense I specify which services my OpenVPN connections can access (just an internal facing NGINX for the most part) and then I can just go to jellyfin.homelab, etc when connected.

Not as smooth as just having NGINX outward facing, but gives me piece of mind knowing my network is locked down

Assuming you don't want to expose these services directly to the internet (I don't recommend it) then you want to set up a VPN to connect back to your home network. Wireguard or OpenVPN are the most commonly used. As far as guides that will depend where/how you want to run it.

You've been given a the usual variety of suggestions, but I suggest also gaining an understanding of networking principles, including RFC 1918 addressing and NAT.

Use cloudflare tunnels. I can access all my localhosts from outside with just one main domain (they are each attached to subdomain of the main domain).

Look at Tailscale docker mod. Adds tailscale inside each arr container and treats them each like a tailscale machine, so on app level you can choose if you expose only in your tailnet or expose to internet.

Another option that might work for you is zerotier.

And you can use sunshine/moonlight to remotely control it.

If you are already messaging around with Dockers, check out NGINX Proxy Manager. It simples the NGINX stuff and gives you a nice interface. So if your make that docker with 8080 and 8443 exposed, in your router port forward 80 to 8080 and 443 to 8443. Then when you go to ramble.chat or plex.ramble.chat it will point to the proper service.

point plex.ramble.chat (cname) to ramble.chat in your registrar. Point ramble.chat (A record) to your public ip (dyndns if you don't have a static)

In NGINX you make a host, plex.ramble.chat and point that to where it lives in your network 10.0.10.5 port 32400 for example.

On the ssl tab, request new cert for plex.ramble.chat with let's encrypt.

Check all the boxes. Now when you go to https://Plex.ramble.chat it will take you to your Plex instance! I would do the same with overseer but not the *arrs. I do req.ramble.chat

Personally I use wireguard. A bit more involved to set up but slimmer IMO. When I put the app on my Android I barely noticed a battery hit with my always on VPN but I can hit my network anywhere from my phone.

Hope this helps!

I would look into Tailscale. This would probably be the easiest to setup.

ssh -D 8080 your.machine and then add localhost:8080 as a proxy to your browser

I use caddy. Previously used traefik, but it's more complicated than I needed.

Caddy can be set to use a single file with all your hosted subdomain listed.

Look at Tailscale docker mod. Adds tailscale inside each arr container and treats them each like a tailscale machine, so on app level you can choose if you expose only in your tailnet or expose to internet.

You could have a look at NginxProxyManager

Thanks for all the suggestions - I think Tailscale is the way to go, it didn't take me long to set up and there is a client for all my devices.

Look at Tailscale docker mod. Adds tailscale inside each arr container and treats them each like a tailscale machine, so on app level you can choose if you expose only in your tailnet or expose to internet.