clarity = "/opt/reshade/shaders/Clarity.fx"
curves = "/opt/reshade/shaders/Curves.fx"
multilut = "/opt/reshade/shaders/MultiLUT.fx"
bloom = "/opt/reshade/shaders/Bloom.fx"
 
reshadeTexturePath = "/opt/reshade/textures"
reshadeIncludePath = "/opt/reshade/shaders/"
depthCapture = off
 
#toggleKey toggles the effects on/off
toggleKey = Home
 
#Clarity.fx
ClarityBlendIfDark=50
ClarityBlendIfLight=205
ClarityBlendMode=2
ClarityDarkIntensity=0.400000
ClarityLightIntensity=0.000000
ClarityOffset=2.000000
ClarityRadius=3
ClarityStrength=0.600000
ClarityViewBlendIfMask=0
ClarityViewMask=0
 
#Curves.fx
Contrast=0.100000
Formula=4
Mode=0
 
#MultiLUT
fLUT_AmountChroma=0.750000
fLUT_AmountLuma=0.750000
fLUT_LutSelector=1
 
#casSharpness specifies the amount of sharpning in the CAS shader.
#0.0 less sharp, less artefacts, but not off
#1.0 maximum sharp more artefacts
#Everything in between is possible
#negative values sharpen even less, up to -1.0 make a visible difference
casSharpness = 0.8
 
#dlsSharpness specifies the amount of sharpening in the Denoised Luma Sharpening shader.
#Increase to sharpen details within the image.
#0.0 less sharp, less artefacts, but not off
#1.0 maximum sharp more artefacts
dlsSharpness = 1.0
 
#dlsDenoise specifies the amount of denoising in the Denoised Luma Sharpening shader.
#Increase to limit how intensely film grain within the image gets sharpened.
#0.0 min
#1.0 max
dlsDenoise = 0.17
 
#fxaaQualitySubpix can effect sharpness.
#1.00 - upper limit (softer)
#0.75 - default amount of filtering
#0.50 - lower limit (sharper, less sub-pixel aliasing removal)
#0.25 - almost off
#0.00 - completely off
fxaaQualitySubpix = 0.75
 
#fxaaQualityEdgeThreshold is the minimum amount of local contrast required to apply algorithm.
#0.333 - too little (faster)
#0.250 - low quality
#0.166 - default
#0.125 - high quality 
#0.063 - overkill (slower)
#fxaaQualityEdgeThreshold = 0.125
 
#fxaaQualityEdgeThresholdMin trims the algorithm from processing darks.
#0.0833 - upper limit (default, the start of visible unfiltered edges)
#0.0625 - high quality (faster)
#0.0312 - visible limit (slower)
#Special notes: due to the current implementation you
#Likely want to set this to zero.
#As colors that are mostly not-green
#will appear very dark in the green channel!
#Tune by looking at mostly non-green content,
#then start at zero and increase until aliasing is a problem.
#fxaaQualityEdgeThresholdMin = 0.0312
 
#smaaEdgeDetection changes the edge detection shader
#luma  - default
#color - might catch more edges, but is more expensive
#smaaEdgeDetection = luma
 
#smaaThreshold specifies the threshold or sensitivity to edges
#Lowering this value you will be able to detect more edges at the expense of performance.
#Range: [0, 0.5]
#0.1 is a reasonable value, and allows to catch most visible edges.
#0.05 is a rather overkill value, that allows to catch 'em all.
#smaaThreshold = 0.1
 
#smaaMaxSearchSteps specifies the maximum steps performed in the horizontal/vertical pattern searches
#Range: [0, 112]
#4  - low
#8  - medium
#16 - high
#32 - ultra
#smaaMaxSearchSteps = 32
 
#smaaMaxSearchStepsDiag specifies the maximum steps performed in the diagonal pattern searches
#Range: [0, 20]
#0  - low, medium
#8  - high
#16 - ultra
#smaaMaxSearchStepsDiag = 16
 
#smaaCornerRounding specifies how much sharp corners will be rounded
#Range: [0, 100]
#25 is a reasonable value
#smaaCornerRounding = 25