16

I just swapped a brushless DC 12V fan on my LG RC185 VCR. Please excuse the abomination that is the MacGyvered contacts. Forgot to order new these: btf6s5fjda072uG.jpg
So that's my excuse. Anyway...

Is it okay to let the cord lean/rest against capacitors and whatnot?

top 13 comments
sorted by: hot top new old
[-] BCsven@lemmy.ca 10 points 2 weeks ago

There could be heat...you can buy sticky backed ziptie loops at places like home depot. Stick one inside that case wall and thread a ziptie through it to hold the wires off the board.

[-] redlemace@lemmy.world 3 points 2 weeks ago

There could be heat

My first thought was "you're wrong, 'caps' (Capacitors) don't generate heat!" But yeah, That's pure based on the title. In the picture the wires seem to rest against a heat-sink. Either way, it's best to tie them out of the way.

[-] BCsven@lemmy.ca 2 points 2 weeks ago

I actually don't know much about electronics, but I have a speaker system where capacitors are known to get hot then the sound starts to crackle after about 5 hours.

Here's some info from the web though...

As electronic devices become smaller and lighter in weight, the component mounting density increases, with the result that heat dissipation performance decreases, causing the device temperature to rise easily. In particular, heat generation from the power output circuit elements greatly affects the temperature rise of devices. However, in applications (switching power supply smoothing, high-frequency power amplifier output coupling, etc.) where large currents also flow in capacitors, the power consumption due to the loss component of the capacitors can increase to the point that heat generation by the capacitors cannot be ignored. Therefore, the temperature rise of capacitors must be suppressed to the range that does not affect the capacitor reliability. An ideal capacitor has only a capacitance component, but an actual capacitor also has an electrode resistance component, dielectric loss, and an electrode inductance component

[-] redlemace@lemmy.world 8 points 2 weeks ago

Capacitors are not supposed to generate heat, nor should the wires, so it's not an issue, but it's not best practice either. if possible, use one of these,

There is a screw nearby. No need to buy it, make one from a suitable piece of scrap plastic

[-] LadyMeow@lemmy.blahaj.zone 4 points 2 weeks ago

Also, hard to tell from the picture, but the heatsunk parts must get hot and are pretty close…

[-] akunohana@piefed.blahaj.zone 4 points 2 weeks ago

Did something similar! Thanks! Used shrinking tubes (without shrinking them. Just for isolation.).

[-] BCsven@lemmy.ca 2 points 2 weeks ago

I wasn't sure. But web says this...

As electronic devices become smaller and lighter in weight, the component mounting density increases, with the result that heat dissipation performance decreases, causing the device temperature to rise easily. In particular, heat generation from the power output circuit elements greatly affects the temperature rise of devices. However, in applications (switching power supply smoothing, high-frequency power amplifier output coupling, etc.) where large currents also flow in capacitors, the power consumption due to the loss component of the capacitors can increase to the point that heat generation by the capacitors cannot be ignored. Therefore, the temperature rise of capacitors must be suppressed to the range that does not affect the capacitor reliability. An ideal capacitor has only a capacitance component, but an actual capacitor also has an electrode resistance component, dielectric loss, and an electrode inductance component

[-] Onomatopoeia@lemmy.cafe 5 points 2 weeks ago

Hey, I'm applauding your MacGyver work. Sometimes it's what you gotta do.

[-] NathanRanch@lemmy.zip 3 points 2 weeks ago

Caps could be a source or receiver of EMI, probably not a realistic issue though. It opens up possibilities in an if-then sense, but those are out there too

[-] abbadon420@sh.itjust.works 3 points 2 weeks ago

Yes, but, if possible, I would cut the wires and recap the ends to make the connection fit better.

[-] akunohana@piefed.blahaj.zone 3 points 2 weeks ago

Thanks! I'll let it be for now, at least until I get my hands on those caps/ends that I cramp on, so that they'll sit properly in this:

38KgZep5KMzmFXV.jpg

CSYqyy9Mfavlh2c.jpg

this post was submitted on 28 Oct 2026
16 points (100.0% liked)

techsupport

3260 readers
8 users here now

The Lemmy community will help you with your tech problems and questions about anything here. Do not be shy, we will try to help you.

If something works or if you find a solution to your problem let us know it will be greatly apreciated.

Rules: instance rules + stay on topic

Partnered communities:

You Should Know

Reddit

Software gore

Recommendations

founded 3 years ago
MODERATORS