1
2
submitted 23 hours ago* (last edited 23 hours ago) by akunohana@piefed.blahaj.zone to c/techsupport@lemmy.world

Does anybody known of hardware that I could slap on to my ONT (one of its ports, just prior to my network traffic leaving the premises) that can gauge TX/RX speeds and amounts? I know I could probably do it with an SBC, but I'm worried about overhead from any OS that I'd deploy.

The purpose is silly. Just for fun.

2
7

I have an android, moto g power. A year or two old.

My phone does this annoying thing when being charged, around 70% it'll make a notification noise and vibrate. It'll continue doing that every couple of minutes until I unplug it. There's never any message or indication why it's doing that. I can only assume it's some kind of battery protection thing. Very annoying at night because I want my phone fully charged for the next day and can't get to sleep with that stupid notification going off.

The weird thing is that it only does it every other time or so.

So, probably related, there are two relatively new options in the battery settings, one for battery health management that's supposed to cap charging at 80% except for one day of the week it goes to 100%, the other for overcharge protection.

I'm not a big fan of bells and whistles if it adds unnecessary complexity but is battery health a legitimate concern or just bullshit extras?

3
19

I have been studying electricity as a hobby, using a highschool textbook, partially documented here. I am trying to leave no stone unturned, meaning that I'm trying to understand any and all concepts and terminology that the book presents. I am now reading about generators and how they produce AC. The chapter also explains how the voltage can at any time/point in the cycle be calculated using sinus. While I understand the gist of it, I don't understand the math behind it, because I simply suck at math. I almost failed math in highschool.... I'm fairly confident I could go on without understanding the math behind why and how the voltage cycles between polarities, but my somewhat neurodiverse brain simply won't let me. I want to, nay, I need to understand it.

So, should I:

  • grab a highschool math book and start from scratch until I reach the chapter on sinus?
  • only read up on sinus and whatever knowledge turns out to be a prerequisite to understand it (with a risk of cascading backwards...)?
  • other recommendations?

This is not a question about how generators work and I am not asking you to explain sinus to me here. I am asking for advise on how to (re)learn math at my age of 30+. I can invest about six hours per weekend. I am eager to learn! Please advise! 😊

4
9

I am new to asking techy questions and it may be obvious or stupid... but my printer seems to be possessed !? It randomly throws out blank pages... and also prints 'Printer Status Reports' by the bucket loads... however many sheets are in the feeder. I have unplugged it, switched it off, taken the paper out (this works as a temporary fix haha), phone HP twice and spent over 2hrs talking through fixes... I asked my ai and she said, change to a USB cable... so I did and now I can't see the bloomin thing. So I unplugged the cable and now it is still throwing out blank pages - and trying to when I remove the paper. Seriously.... this printer can not be dead !? It still prints ! If its dead or been taken over by the print ghosts, just tell me straight and I will stop fighting. BUT.... if it is the case - I don't want another printer connected to HP... I don't want instant ink or nosey manufacturers looking at what I am doing. I need recommendations for a printer that is OFF LINE and private... just on my network nice and peacefully doing it's thing....Is that even possible nowadays ?

5
8
submitted 6 days ago* (last edited 6 days ago) by akunohana@piefed.blahaj.zone to c/techsupport@lemmy.world

The question is purely academic, so there is no need to discuss the legality of the matter. :)

The drone is probably an advanced model, judging from the high altitudes it was hovering at the other day.

Would I need to know the exact make and model of the drone in order to know what band and exact channels its radio uses?

Followup question 0: would it be possible to make the jamming signal something legible, such as a song, for trolling reasons? Or does the signal have to be of a certain periodic kind? A certain sine wave?

Followup question 1: is the signal encrypted between the controller and the drone? If it is, I suppose there is no way to hijack the drone. Is it still possible to create noise that the drones receiver must pick up?

Followup question 2: if there was an old, unused 20 meter tall TV antenna within a 500 meter radius of said drone, would hooking my transmitter up to it help amplify the jamming signal? Or would the power requirements be ridiculously large in such an antenna, with all the added resistance? I never knew the technical specs of those.

6
8

Hey everyone,

I'm having a weird issue with a Dell Latitude 7320 Detachable after replacing the battery.

Here's what happened:

After installing the replacement battery, the device stopped booting.

The charging/power LED lights up when connected to USB-C power.

When pressing the power button, the keyboard and stylus light up.

After a few seconds, the power LED blinks twice and the device shuts down.

I switched back to the original battery, and the device actually managed to boot into Dell Diagnostics once.

After that, it stopped booting properly again.

At one point, the screen stayed black except for a thin horizontal white line across the entire top of the display. It remained powered on.

Now even that white line has disappeared.

I'm wondering if this could be a broken BIOS, maybe some controller issue.

The fact that it managed to enter Dell Diagnostics once with the original battery makes me think the motherboard might not be completely dead.

Is there a way to force BIOS recovery or reset it on this specific model?

Any ideas?

Thanks!

7
2

Thinkpad L13 Gen2 Amd running latest Debian (though it's not related to OS, had this on Ubuntu as well), the backlight works for a day or so, then stop working. I have to do a power drain / hard reset (hold power button for like a 30 seconds) for it to start working again. I'm wondering if anyone's come up with a solution to this. Any suggestions are appreciated.

8
8
submitted 1 week ago* (last edited 1 week ago) by ComicalMayhem@lemmy.world to c/techsupport@lemmy.world

I'm so utterly flabbergasted. The tutorial page says to use the CMake integration and includes a link, but the link sends me to a page with a ton of hyper specific information that doesn't exactly walk me through set up, and I actually cannot find any real guides to help with this. I tried copy pasting the Cmake snippet into the CMakeLists.txt and running cmake -B build but it broke, with 3 errors: Cannot find source file: test.cpp, No SOURCES given to target: tests, and No SOURCES given to target: custom-main-tests. When I comment out the offending line (add_executable(tests test.cpp)) I end up with the error Cannot specify link libraries for target "tests" which is not built by this project. I've already installed Catch2 as a system package via my software manager (Linux Mint). Is this a directory issue? Am I supposed to clone a git repo or copy-paste libraries in somewhere? I don't understand and the CMake integration link on Catch2's tutorial page is seemingly of no help.

Not using any IDEs, just my default text editor and Xed. I am also not at all versed in CMake whatsoever, like, at all. No real understanding of what it is or what it does or how it works, it's basically magic to me.

9
21

I was relaxing in my sofa when I heard a pop. Then a clack. Then a beep.

I had forgotten to turn off the stove when removing a pot from it and my rice cooker's power cable dropped onto it. I suppose the first pop was the cable igniting. The clack was the breaker tripping and the beep was my UPS turning on. Nobody was hurt.

Resistance increases with heat. My power outlets supply 220~240 volts. Since I = V / R, the increased heat and resistance in the rice cooker's power cable should have decreased the current, if the outlet voltage is constant. Or, is it so that the system actually tries to compensate with more voltage within some range set by my electricity supplier? Or, was it something else entirely that tripped the breaker?

Please teach me! 😊

10
13

A few month ago, i used my old gaming laptop (HP Omen 15 (2016)) to start a small home server with Yunohost. I recently got an old PC for a few bucks, with a Intel Pentium D 820 as CPU. I thought that as its specs were closer to my hosting needs (just a bunch of files for archives and collaboration with Trilium, no media streaming or anything), I could use the old PC as the server and use my laptop for something else, or give it to someone.

But I tried to check the power consumption of the Pentium D 820, and found 148W idling and 233W under load, while the Omen 15 is probably around 20W idling and 120W under load. So apparently the gaming laptop has both better performances and lower consumption (i guess the fact it's a laptop and the better efficiency of more recent tech are two of the main reasons).

If i'm correct on that, does it make sense to stay with the laptop just because it'll probably consume less ? Or is there any reason to choose the old PC ?

Both machines specifications details

HP Omen 15 (2016) Old PC
CPU i7-6700HQ 3.5GHz Pentium D 820 2.8GHz
RAM 16Gb 1Gb
GPU GTX 965M None
PSU 120W adapter ? H280P-00 280W
11
50

I have never seen this many warning signs on anything that I have ever bought. I know that I'm supposed to suck away the soldering fumes, even if I use lead free solder, which I'm going to do with a 12 volt computer fan fitted with a carbon filter. But what the heck is in the flux that will damage my nervous system... 💀 putting my mask back on... 😷

o7ljacOteNY34fG.jpg

HXe8jjSm95Zk5rd.jpg

Uap7IbkvstMg6co.jpg

4ibJ0aFHkA6fCh6.jpg

bPKWwEJUO6pMF6p.jpg

O7KLlZjhTNt44nU.jpg

12
10
submitted 2 weeks ago* (last edited 2 weeks ago) by Fortatech@gregtech.eu to c/techsupport@lemmy.world

I have a family member, whose phone screen broke, and they want to get their data off it. Developer tools are not enabled, so i fear I can't do anything with ADB, so i guess a hub is my best option (I have been meaning to buy one for myself anyway)

Having googled for a bit i noticed that i need something that is OTG compatible, but none of the hubs seem to mention anything OTG related.

Thank you in advance.

edit: the phone is an OnePlus, will ask what yhe model is

edit2: OnePlus 6

13
10
submitted 2 weeks ago* (last edited 2 weeks ago) by Seimhe@lemmy.world to c/techsupport@lemmy.world

I’ve spent so many hours on this. I’m trying to get Star Trek TNG to play at 7:30pm on Mondays and Fridays (all seven seasons, sequentially). But my player still just shows “Channel is Offline”.

I’ve scanned local media and the show is detected. I created a channel and a schedule, and set the collection type to the entire series. The playout is paired with the channel. The m3u link shows “Channel is Offline” in IINA (like VLC but for macOS).

Any help appreciated. I’m a bit overwhelmed by the breath of options and documentation.

14
16

I just swapped a brushless DC 12V fan on my LG RC185 VCR. Please excuse the abomination that is the MacGyvered contacts. Forgot to order new these: btf6s5fjda072uG.jpg
So that's my excuse. Anyway...

Is it okay to let the cord lean/rest against capacitors and whatnot?

15
14
submitted 3 weeks ago by lena@gregtech.eu to c/techsupport@lemmy.world

I'm constantly worried that I didn't get enough sleep, so I'm hoping to prove to myself that that is not the case. How could I do that without sending all of my health-related data to Google or some other company?

16
13
submitted 3 weeks ago* (last edited 3 weeks ago) by akunohana@piefed.blahaj.zone to c/techsupport@lemmy.world

Edit4: there seems to be a correlation between whether the VCR's timer is counting (meaning it's able to read data on the tape) and whether there is any visual noise.
f5V3eBzyO44TpGL.gif

Edit3: I cleaned the whole pathway that the tape travels within the VCR, to no avail, but I experimented with extremely lightly giving the "tension arm" (it's called something else for Walkmans...) a little more tensions, and lo and behold, at the very least it influenced the duration of each individual noise occurrence. Push to hard and the noise in the attached video above disappears, but then other artifacts are introduced. On another Sharp VCR that I had, rest in peace, you could actually adjust the tension belt by hooking it further "back", giving it more tension, but not on this LG. Here is the part in talking about:
6mIXXa4oy9BsUAU.png

18wBK7Pex9gi9Zl.png

Edit2: As stated by @voodoo3dfx@retrolemmy.com the creases on the tape seem to be a huge contributing factor. Interestingly, the noise seems to temporarily improve if I manually, with my fingers, spin the two wheels/gears in opposite directions to give the tape a bit more tension. It soon degrades again though.

Edit: The VCR is an LG RC185 and the make of the tape is unknown. The underside of the tape lid say P-55. Also, I noticed these fairly evenly distributed physical lines/indentations on the tape: DYoaTINnGIww6qg.gif

This phenomenon, in which noise appears at the top, slowly travels downwards and disappears at the bottom happened all through the tape, from start to end, at quite regular intervals, perhaps every ten seconds.

I have cleaned the read/write head of the VCR, which already looked fine regardless. By clean I mean shiny, because I'm a layperson...

17
12
submitted 3 weeks ago by pedz@lemmy.ca to c/techsupport@lemmy.world

I'm looking for a new set of router/APs to cover a whole house in a mesh setup, that doesn't involve using an app, or creating an account with the manufacturer. It has to work locally, with the configuration accessible from a browser. I repeat, no app and no online accounts. Just devices that can act as a router + repeaters, that can be configured from a browser. A bonus would be to have SMA ports so that antennas can be connected to them.

The current setup consists of only two Asus RT-AC66U, and the range sucks. They'e getting old, I don't want more of these, and the one serving as a mesh repeater often stops responding for a few seconds. I made the mistake of buying a pack of TP-Link Deco and I ended up returning them because they require an app and online account to configure.

Any suggestion meeting those requirements will be appreciated.

18
19
Digitizing VHS (lemmy.nz)
submitted 3 weeks ago* (last edited 3 weeks ago) by akunohana@piefed.blahaj.zone to c/techsupport@lemmy.world

I have noticed on the handheld cameras and on this VCR, which I use for digitization, that they are quite smart in the way that (even) if I fast forward the tape, the counter stops as soon as there is no video/data, which is really useful when setting up bash scripts for the recording. However, some tapes display video and audio when monitored - in my case with mpv on Linux - while the VCR's counter is still. The video and audio signals are perceivably degraded with a lot of noise and distortion.

Does this mean that VHS tapes lose magnetic charge over time? Does it mean that all ferromagnetic media lose charge over time?

I hope my ungrateful colleague (see this post) will still be happy for the little I was able to recover without professional equipment. 🥲

19
26
submitted 1 month ago* (last edited 1 month ago) by akunohana@piefed.blahaj.zone to c/techsupport@lemmy.world

This community has helped me in so many fields, I don't even know how to begin expressing my appreciation for your help! I'll just pick out one example of the many. That'll have to do.

THANK YOU FOR THE ADVICE ON CLEANING A POTENTIOMETER BEFORE ATTEMPTING A SWAP

My audio cassette deck is now outputting evenly on both channels! 🥰🥰🥰

RFdIBVRR0UdfPjs.jpg
Pictured here, taping Cyndi Lauper's She's So Unusual 🥰🥰🥰

20
33
submitted 1 month ago* (last edited 1 month ago) by akunohana@piefed.blahaj.zone to c/techsupport@lemmy.world

I bought these possibly Kenko cfe auto extension tubes (26 + 12 + 11 [mm]) with Canon FD mounts. I'm using them on a really sweet Canon FD 135/f2.5. Normally, I simply input those values into the digital camera's "manual lens info" slot in order for the in body image stabilization to work better, but I'm not sure what to input here. Should I simply add the above tube lengths to the total focal length (135 + 49)? And what about the visually obvious loss in light/aperture. What would the new value be there?

Bredit (brag edit): CDUMRxi2czpbVzU.png

21
7
submitted 1 month ago* (last edited 1 month ago) by akunohana@piefed.blahaj.zone to c/techsupport@lemmy.world

I have fine tuned my fan curves in the BIOS and normally, even when I used to game, the fans wouldn't speed up unless there was actual heat to dissipate. Now, I'm digitizing analog tapes using ffmpeg on Linux with the encoder h.246. This smart little thing auto detects the number of CPU cores available - 18 in my case - and uses them all. As soon as I hit ENTER ("start" or the likes for Windows users), my fans blast at full speed. Not that I'm trying to determine CPU temps by hand feel, but the air coming out of the chassi doesn't feel hot at all - at least compared to when I used to game, but maybe that was more the heat from the GPU? Even so, how could the CPU heat up to temps requiring maximum fan speed in an instant? Or is it so that the fans (or their controller or the likes) anticipate high temps and spin up preemptively?

22
11
submitted 1 month ago* (last edited 1 month ago) by akunohana@piefed.blahaj.zone to c/techsupport@lemmy.world

Edit2: There seems to be an "M" in the top left corner, but I'm not sure:
QJLoIfZsmMDfsnA.jpg

Did some fucktard for any reason scrape off the part numbers? I can just make out some symbols and shapes if I illuminate the chip from the side and shadow is cast on the miniscule deformities.

uEYtlkLk1OIU4IL.jpg

gqkJItDe2k0svSo.jpg

Edit: could I perhaps dust/brush some white powder on its surface to make it more visible?

23
5
submitted 1 month ago* (last edited 1 month ago) by akunohana@piefed.blahaj.zone to c/techsupport@lemmy.world

My audio cassette deck has a panning knob (left/right), which I assume regulates the strength of the two channels of a stereo signal. When I turn the knob, there is a rustling sound and the sound is intermittent. I have to manually push the knob in some direction to have both channels make contact.

Is such a knob a simple potentiometer that I could replace? Or is there some sort of maintenance to be done on it? I have already used compressed air in various angles directed at the base of the part and at the small openings around knob itself.

Edit: description of the knob in question
bnH6OKP4UsZGERS.png

Edit: view of the PCB on which the "potentiometer" in question rests
sntTm351Qbmqf4N.png

24
11
submitted 1 month ago* (last edited 1 month ago) by akunohana@piefed.blahaj.zone to c/techsupport@lemmy.world

I am digitizing analog PAL video from VHS, VHS-C, Hi8 and Mini DV cassettes. I recently learned that analog to digital conversion is done by sampling and quantizing the continuous analog signal into discrete snapshots and values. See for instance: https://www.monolithicpower.com/en/learning/mpscholar/analog-to-digital-converters/introduction-to-adcs/fundamental-concepts

In light of this, I decided to open up my video ADC in order to get the name of the IC that does the job, because there was just no way that I'd be able to read the IC's resolution off of Linux, considering that the signal had gone through a capture card and ffmpeg's filters after the conversion.

I learned that the IC is an MS1858E by Macro Silicon, which quantizes with an 8-bit resolution (not to be confused with image size resolution!) and samples at 54 MHz sampling rate, although my Chinese is a bit rusty, so take this with a grain of salt... Here: https://www.lcsc.com/datasheet/C42374496.pdf

Question: the 8-bit quantizing resolution means that my little ADC can output at most 256 (2^8) video values. That probably includes not only the color space, but all other information too... If I just let this all go and ask myself whether I'm satisfied by the end results of my digitizing, then yes, I am satisfied. But it also makes me wonder whether paying $200 for a professional ADC is worth it (as opposed to $20 for my current one) if it comes with greater resolution? Like 16-bit? I can't even know what I get before buying and opening up the product, because the retailers don't exactly write that in the product description...

Edit: I’m asking whether investing in an ADC that can work with more bits would make a significant improvement in subjective video quality, considering that the analog signal is at most early 2000’s PAL.

25
8
submitted 1 month ago by lena@gregtech.eu to c/techsupport@lemmy.world

Me and a few classmates are hoping to set something like this up for shared class notes.

Obsidian with the Relay plugin seems perfect, but sadly even if you self host it you have to pay to have more than 3 users, and even if you do, you're limited to 6 users. The Logseq DB version also seems nice, but it's in alpha, so I don't trust it with important data.

view more: next ›

techsupport

3260 readers
9 users here now

The Lemmy community will help you with your tech problems and questions about anything here. Do not be shy, we will try to help you.

If something works or if you find a solution to your problem let us know it will be greatly apreciated.

Rules: instance rules + stay on topic

Partnered communities:

You Should Know

Reddit

Software gore

Recommendations

founded 3 years ago
MODERATORS