32
Bambu Regrets (lemmy.world)

I won a bambu as a gift because I had a chinese printer that never worked and wanted something easy and "dumb friendly" no more days amd days looking up a problem. Well mine came with a problem and after 12 HOURS i still wasn't able to load a filament. Reading about bambu support I realized I was going to spend a REALLY long time and they wouldn't fix it so I just returned for a full refund. I'm very frustrated and almost giving up 3d printing all together because it's the second defective printer I get.

top 30 comments
sorted by: hot top new old
[-] FatVegan@leminal.space 2 points 1 hour ago

I got a elegoo carbon 2, it was suggested bh someone on this forum i think. I had two diy printers before, but it was always a situation of: i really hope it works, because i don't know enough to fix it. The printer is really user friendly and super easy to use, at least compared to what i was used to.

My third print failed because of some filament issue and i had to learn how to take apart the printhead and unclog the filament. I did this multiple times by now. Sometimes filament broke off in the tube because it was brittle for some reason, whoch isn't a big deal but time intensive for no reason. Right now, the filament doesn't cut and retract, which is important for multi coloured prints, and i didn't have it in me to figure out why and take the printhead apart again.

Thing is, i guess it is a hobby where you always have to tinker and figure out something. Even the easiest printer that always worked, at some point you have to fix something or change a belt or printhead or whatever.

[-] brillotti@lemmy.world 1 points 58 minutes ago

Mine stopped loading filament after about a year and a half of ownership. All I had to do was disassemble the extruder, remove a bit of loose filament inside, put it back together and then it worked again. Bambu Lab provides handy guides for routine maintenance like this https://wiki.bambulab.com/en/P1/maintenance/extruder-cleaning-guide

[-] Strider@lemmy.world 2 points 1 hour ago

Don't feel bad. Not all hobbies are for everyone. Sometimes we know before trying, sometimes after.

I chose to stay away from 3d printing since it has potential to consume my life. And me going mad. So no, not going to do that.

For the occasional print I could pay someone, like with a copy shop.

[-] daannii@lemmy.world 4 points 2 hours ago* (last edited 2 hours ago)

Unfortunately, as others have said, they all require mechanical tinkering.

Personally as someone who had an ender first (requires a lot of work , constantly, and replacement parts, constantly), I can say my Bambu didn't even need anything until around the 1000 hour mark. And their wiki guide is incredibly helpful. They also have videos.

They haven't always been helpful for every issue. But honestly it's going to be one of the easier printers to deal with.

Assuming you started with an A series.

They do get more complicated to fix with their higher end models.

Regardless of what brand you go with. First step is learn how to use Google. Search YouTube and Reddit. And you likely will find a solution to your problem.

You will absolutely have to manually search. Don't use ai searches. Ai can't help you with something this complex.

[-] stealth_cookies@lemmy.ca 7 points 9 hours ago

Yes getting poor support for a DoA product sucks, but you do need to be aware that every 3D printer will have things go wrong periodically, they are complicated mechanical devices and parts need maintenance and wear out over time.

[-] Ember@pie.eyeofthestorm.place 5 points 6 hours ago

It's not even poor support. I just reread the post and they said they looked at how long support can take, not that they even attempted to reach out for support.

[-] stealth_cookies@lemmy.ca 1 points 52 minutes ago

Yeah you're right, I didn't read it that way at first. If someone isn't even willing to try then it is probably the right choice to return it and accept the hobby isn't for them. Even if they really didn't want to try with support for whatever reason, I bet whatever was wrong was either solved by someone else with a quick search online and if it needed a new part it was probably a modest cost to fix.

[-] _haha_oh_wow_@sh.itjust.works 16 points 13 hours ago* (last edited 13 hours ago)

3D printing is definitely more of a tinkerer's hobby IMO

I have a Creality CR10S (piece of shit) and a Prusa MK3s (pretty good, very reliable): Both definitely require maintenance, calibration, etc.

[-] SaveTheTuaHawk@lemmy.ca 0 points 12 hours ago

3D printing is definitely more of a tinkerer’s hobby IMO

it was until Bambu and Snapmaker changed the game. They forced Prusa and others to get their shit together.

[-] _haha_oh_wow_@sh.itjust.works 10 points 11 hours ago* (last edited 11 hours ago)

You say that but eventually every printer needs maintenance and repair. For what it's worth, I am already familiar with Bambu printers and disagree with the assertion that Prusa didn't "have their shit together". I think Bambu, on the other hand, needs to get their shit together when it comes to being customer friendly, free, and open source like Prusa.

[-] phx@lemmy.world 1 points 11 hours ago* (last edited 11 hours ago)

Most of what I've heard about Bambu was then being a good printer for beginners due to minimal configuration/maintenance and generally good support for generally decent prints, with the trade-off being more lock-in and less customizability.

For myself, I've had a bunch of really cheap printers starting from an old Monoprice and then a bunch of Anycubic. The latter is kinda a middling brand but actually my support experience has been pretty good (no issues exchanging a printer that had a manufacturing defect when received) and the things have generally run well enough to fill my shelves with various miniatures as replace a multitude of parts etc.

That said, I'm using modified firmware on my Kobra so that I don't need to use their software on my PC

[-] DudeImMacGyver@kbin.earth 3 points 11 hours ago

Crazy take, Prusa is the better company.

[-] CmdrShepard49@sh.itjust.works 3 points 9 hours ago

Depends on how you define "better." Price wise and innovation wise, Bambu ate their lunch selling $300 enclosed core XY machines with multi-material capabilities while Prusa was still selling $1000 single filament bed slingers.

[-] papalonian@lemmy.world 2 points 6 hours ago

I'd love a prusa but any of their machines that do what I would want cost more than my car

[-] richardgunther@twit.social 7 points 12 hours ago

@MissJinx Why not exchange it? Bambu printers typically "just work." I've bought 3 and plan to upgrade again sometime in the next year or so.

[-] DScratch@sh.itjust.works 5 points 8 hours ago

Op didn’t even try support before returning it.
I’ve also bought for myself, the community workshop I help run, friends and family a mix of p1s and a1- minis and they all worked out of the box with little fuss.

The only one that’s needed any real parts (after months of use) is the a1 at the workshop, but that thing sees use.

[-] Ember@pie.eyeofthestorm.place 5 points 11 hours ago

If you can't load a filament after 12 hours, I'm going to say that's user error.

[-] CmdrShepard49@sh.itjust.works 5 points 9 hours ago

Agreed, I've had to strip my toolhead down due to my own impatience with a clog and it takes like 15 minutes at most. PTFE to filament sensor to hot-end is the entire filament path so what took 12 hours of work without even leaving this user with an idea of what the issue was?

[-] FatherPeanut@pawb.social 2 points 8 hours ago

I feel a bit of this is happening here: XKCD: "Average Familiarity". Most people who aren't very familiar with the ins and outs will likely look at what you'd said and not instinctively be able to follow along. If your hobby is printing, its fair to say you know a lot, but if your printing is just a means to supplement another hobby, you might not have doven deep enough into research to know all of it.

Having to troubleshoot a system you're unfamiliar with and new to is complicated. The diagnosis step can feel monumental when you don't know how every component functions in relation to what else. Pair that with a cheap entry-level printer, and it's what made my first experiences with 3D printing reeealy drawn out to the point I'd given up multiple times. When OP says they spent 12 hours working on it, I gotta say, I really believe it.

[-] CIA_chatbot@lemmy.world 8 points 13 hours ago

Snapmaker U1, incredible printer. Easy to use. I don’t know about the support because I’ve never needed it. I have a couple of thousand hours on it so far and my bambu just sits in the corner gathering dust

[-] SaveTheTuaHawk@lemmy.ca 3 points 12 hours ago* (last edited 12 hours ago)

I have a printer farm with a bunch of Prusas, an H2C and recently we bought two U1s.

The U1 has a success sheet behind it and it's over 42 prints in just a month. Very complex prints of protein models.

[-] Rhaedas@fedia.io 2 points 13 hours ago

Thanks for the mention. I'm not into 3D printing yet, but had looked around to get familiar with things and was going to settle for a single color type since the whole poop thing seems ridiculous if you can't easily capture that waste back. Looking at this one, it makes sense to spend a bit more to get multiple heads to do different colors and material at once. Imagine if color printing on paper had you spit out a bunch of one color into the trash to switch to a new one.

[-] CmdrShepard49@sh.itjust.works 1 points 9 hours ago

since the whole poop thing seems ridiculous if you can't easily capture that waste back

Its not as bad as you think especially when you're comparing them to lower quality printers that cause you to throw a bunch of half finished prints in the trash due to print errors. You can also avoid this if you use/make models that have the colored parts split out so you're only printing one color at a time, or minimize waste by printing multiples of whatever multicolored object you're printing. The waste is the same whether you're printing 1 or 50.

Some prints its unavoidable, but I certainly feel like I've wasted way less plastic with my Bambu printers than I did with the bed slinger I had before it.

Multiple toolheads are probably the better way to go but these introduce their own issues and can lead to print failures as well since they're way more complex than a single toolhead.

[-] SaveTheTuaHawk@lemmy.ca 2 points 12 hours ago

multiple toolhead printers still use a purge tower which is waste.

[-] CIA_chatbot@lemmy.world 1 points 11 hours ago

I usually purge into the fill and support, and the poop is almost non-existent

[-] scallisto@retrofed.com 1 points 8 hours ago* (last edited 8 hours ago)

If you do want to start 3D printing, I would highly recommend avoiding Bambu, as somebody who has an A1, since they locked down their software to prevent third-party software, accessories, and other bits from working without enabling some stupid "developer LAN only mode". They have also been very aggressive against small open-source projects (see fork of OrcaSlicer being attacked), despite their own slicer software being a fork of a fork. I do not recommend Bambu printers any more, especially since the competition has gotten very good. Bambu printers are no longer the best option, and they do not "just work" as some people suggest

Want something that is excellent value? The Elegoo Centauri Carbon is awesome and has an enclosure AND CoreXY (faster and more reliable prints), while the A1 I have has neither. You want something high performance? The Prusa Core One is more reliable than similarly priced Bambu machines, is manufactured in Czechia 🇨🇿, and super repairable too. Plus, it is CoreXY, and supports multi-material and has an optional toolchanger add-on too! If you want a very good value toolchanger? The Snapmaker U1 is cheaper than both Bambu and Prusa with a toolchanger + they use a variant of OrcaSlicer as their slicer software (turns out you don't have to be a dick to the open source community to make a good 3D printer!)

[-] kalapala@sopuli.xyz 6 points 13 hours ago

If you want a reliable machine out of the box just buy prusa.

[-] tristan@aussie.zone 7 points 12 hours ago

Outside of Europe, prusa are often unaffordable compared to every other brand. Here in Australia it's nearly twice the price of a bambu equivalent, and 4-6x the cheaper Chinese brands

Because of that, there's very few places that even sell it so you struggle to find availability on top of the price

[-] SaveTheTuaHawk@lemmy.ca 5 points 12 hours ago* (last edited 12 hours ago)

That's hilarious. Prusa beta tests in the "community". I do not understand the cult of Josef.

[-] Imgonnatrythis@sh.itjust.works 2 points 11 hours ago

I'd count it as a blessing in disguise. I think in the long run you'll be happier you are involved in Bambu's nonsense.

I'm biased toward prusa, but there's a lot of good options that let you easily do amazing prints and protect your privacy and are more developer / maker friendly.

this post was submitted on 19 Nov 2026
32 points (90.0% liked)

3DPrinting

24361 readers
126 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: or !functionalprint@fedia.io

There are CAD communities available at: !cad@lemmy.world or !freecad@lemmy.ml

Rules

If you need an easy way to host pictures, https://catbox.moe/ may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![]()

Moderation policy: Light, mostly invisible

founded 3 years ago
MODERATORS